Changzhou Edaweld Trading Company Limited

Product Categories

Review
  • “I purchased this H07 40 Gas Cutting Tsui after looking at various of these products for some time. In the end they all looked to be much the same so I decided upon this one based on the price.”
    Khaled Mohemmed
    470Sailing
  • “The H07 40 Gas Cutting Tsui price is preferable with good condition,recommend.”
    Sujoy Poddar
    Geographics
  • “Thanks for fast delivery”
    Nasirin Sani
    3too
  • “These are PERFECT! You may purchase them with complete confidence!”
    Alejandro Theus
    310atable
  • “Good delivery make me surprise. The H07 40 Gas Cutting Tsui also seems great.”
    Bobby Gondoza
    Comeaux Caps

H07 40 Gas Cutting Tsui

- manufacturer, factory, supplier from China

(Total 12 Products for H07 40 Gas Cutting Tsui)

  • H07-2 Gas Cutting Nozzle

    H07-2 Gas Cutting Nozzle

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    H07-2 Gas Cutting Nozzle The principle of gas cutting general cutting is the use of oxygen cutting method which is the use of sparks is oxygen sponge spark or oxygen propane sparks, the recent use of oxygen propane widely. Gas cutting (oxygen cutting) is a cutting method that utilizes the chemical reaction of iron and...

    Contact Now

  • H07-40 Copper Gas Cutting Nozzle

    H07-40 Copper Gas Cutting Nozzle

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    H07-40 Gas Cutting Nozzle Cutting the deformation of the occurrence of cutting the biggest problem is the cutting deformation. This is the local heating of the material and his accompanying shrinkage, plastic deformation and internal stress. Or the deformation of the material in the cutting nozzle and cutting line is...

    Contact Now

  • H07-6 Gas Cutting Nozzle

    H07-6 Gas Cutting Nozzle

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    H07-6 Gas Cutting Nozzle Flame cutting, the commonly used combustible gases are acetylene, gas, natural gas, propane, etc., in general, the burning speed, high combustion value of the gas for thin plate cutting; combustion value is low, slow burning flammable gas more suitable In the thick plate cutting, especially in...

    Contact Now

  • H07-40 Brass Gas Cutting Nozzle

    H07-40 Brass Gas Cutting Nozzle

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    H07-40 Gas Cutting Nozzle The main process factors that affect the process of gas flame cutting (including cutting speed and quality) are: (1) the purity of cutting oxygen; (2) the flow rate, pressure and oxygen flow of the cutting oxygen; (3) the flow rate, momentum and angle of attack of the oxygen flow; Thermal...

    Contact Now

  • Small Copy Type Machine Cut Tsui

    Small Copy Type Machine Cut Tsui

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    Small Copy Type Machine Cut Tsui When you use the oxygas torch method to cut metal, the oxidation of the metal is extremely rapid and part of the metal actually burns. The heat, liberated by the burning of the iron or steel, melts the iron oxide formed by the chemical reaction and accelerates the preheating of the...

    Contact Now

  • G07-30 Gas Cutting Tsui

    G07-30 Gas Cutting Tsui

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    G07-30 Gas Cutting Tsui Each manufacturer makes many different types of cutting tips. Although the orifice arrangements and the tips are much the same among the manufacturers, the part of the tip that fits into the torch head often differs in design.

    Contact Now

  • Brass LPG Japan Gas Cutting Tsui

    Brass LPG Japan Gas Cutting Tsui

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    Brass LPG Japan Gas Cutting Tsui To make clean and economical cuts, you must keep the tip orifices and passages clean and free of burrs and slag. If the tips become dirty or misshapen, they should be put aside for restoration. Figure 4-14 shows four tips: one that is repairable, two that need replacing, and one in...

    Contact Now

  • G07-100 Natural Gas Cutting Tsui

    G07-100 Natural Gas Cutting Tsui

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    G07-100 Natural Gas Cutting Tsui Clean the orifices of the cutting torch tip in the same manner as the single orifice of the welding torch tip. Remember: the proper technique for cleaning the tips is to push the cleaner straight in and out of the orifice. Be careful not to turn or twist the cleaning wire. Figure 4-15...

    Contact Now

  • G07-300 Gas Cutting Tsui

    G07-300 Gas Cutting Tsui

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    G07-300 Gas Cutting Tsui If the tip seat is dirty or scaled and does not properly fit into the torch head, heat the tip to a dull red and quench it in water. This will loosen the scale and dirt enough so you can rub it off with a soft cloth. OREDR NO. NAME MODEL NO. SIZES CX045 G07-300 Gas Cutting Tsui 1#2#3#-4# 1.8...

    Contact Now

  • GKJ3 Long Copper Cut Tsui

    GKJ3 Long Copper Cut Tsui

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    GKJ3 Cut Tsui MAPP GAS CUTTING TIPS.- Four basic types of MAPP gas cutting tips are used: two are for use with standard pressures and normal cutting speeds, and two are for use with high pressures and high cutting speeds. Only the standard pressure tips, types SP and FS, will be covered here since they are the ones...

    Contact Now

  • Natural Brass Gas Roast Tsui

    Natural Brass Gas Roast Tsui

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    Natural Gas Roast Tsui The cutting angle between the cutting tip and the cutting piece directly affects the gas cutting speed and the rear drag amount. The size of the cutting angle is mainly determined by the thickness of the workpiece. When the gas is cut 4 ~ 20mm thick steel plate, the cutting mouth should be...

    Contact Now

  • Natural Copper Gas Roast Tsui

    Natural Copper Gas Roast Tsui

    • Brand: OEM/EDAWELD
    • Packaging: Carton
    • Supply Ability: 10000
    • Min. Order: 100 Piece/Pieces

    Natural Gas Roast Tsui The principle of flame cutting is the use of gas and oxygen mixed combustion heat (that is, preheat the heat of the flame) preheat the metal surface, so that the preheat metal to the combustion temperature, and to be activated, and then sent to high purity, high The speed of cutting oxygen flow,...

    Contact Now

Categories

High Quality Products

Send Us a Message

We didn't put all products on website. If you can't find the product you're looking for, please contact us for more information.

Home > H07 40 Gas Cutting Tsui

Send Inquiry

YAO SHANSHAN

Ms. YAO SHANSHAN

Tel:86-0519-85860058

Fax:86-0519-85860058

Mobile Phone:+8618961200813

Email:sandra_yao@edaweld.com

Address:No.382, Changhong East Road, Yaoguan Town, Wujin District, Changzhou City,Jiangsu, China, Changzhou, Jiangsu

Mobile Site

Home

Product

Phone

About Us

Inquiry

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send